HOME > °¢Á¾ ¼¿·ºÅÍ/ºÐ¹è±â/º¯È¯ ÄÁ¹öÅÍ > 2. DVI ÄÉÀ̺í / DVI ±¤ÄÉÀ̺í Á¦Ç°±º > DVI-D ½Ì±ÛÄÉÀ̺í
È®´ëº¸±â

[17746]EXTRON HDMI UTP(·£) Àü¼Û±â 100¹ÌÅÍ Àü¼Û°¡´É[ DTP DVI 301 Tx / Rx ][°¡°Ý¹®ÀÇ]
½º   Æå : Long Distance DVI Twisted Pair Extender
Á¦Á¶»ç : EXTRON
¼ö   ·® : °³
ÆǸŰ¡ : 0 ¿ø
Àû¸³±Ý : 0 ¿ø
100000ÀÌ»ó ±¸¸Å½Ã ¹«·á¹è¼Û ³³Ç°/³³±â °ßÀû¿äûÀº ÀüÈ­Áֽñ⠹ٶø´Ï´Ù.
Àå¹Ù±¸´Ï´ã±â ¹Ù·ÎÁÖ¹®Çϱâ
ÀÌÀüÈ­¸é
Model Version Description Part #        
DTP DVI 301 Tx   DVI Transmitter   60-1213-12      
DTP DVI 301 Rx   DVI Receiver   60-1213-13

UTP ·£ DVI ½ÅÈ£À» (¿Àµð¿ÀÆ÷ÇÔ) 100¹ÌÅÍ Àü¼Û°¡´ÉÇÑ ¸®ÇÇÅÍ

  • Energy-efficient external universal power supply included with Tx models, part # 70-775-01 — Provides worldwide compatibility, low power consumption, and reduced operating costs.

    Video
       Maximum data rate  6.75 Gbps (2.25 Gbps per color)
       Maximum pixel clock  165 MHz
       Resolution range  Up to 1920x1200 or 1080p @ 60 Hz; 8, 10, or 12 bit color depth
       Formats  RGB and YCbCr digital video
       Standards  DVI 1.0, HDMI
    Video input and loop-through — transmitter
       Number/signal type  1 single link DVI-D (or HDMI*) input
    1 single link DVI-D (or HDMI*) local loop-through
       Connectors  2 female DVI-I
    Interconnection between transmitter and receiver
       Connectors  2 female RJ-45 per unit for 2 cables connecting the transmitter and receiver
    TP1 output transmits digital video, embedded digital audio, RS-232, IR, and remote power.
    TP2 output transmits analog stereo audio.
       Termination standards  TIA/EIA T568A or T568B
       Signal transmission distance  330' (100 m) using CAT 5e/6/7 UTP or STP cable (24 AWG or better)
    Video output — receiver
       Number/signal type  1 single link DVI-D (or HDMI*)
       Connectors  1 female DVI-I
    Audio
       Gain  Unbalanced output: 0 dB; balanced output +6 dB
       Frequency response  20 Hz to 20 kHz, ¡¾0.05 dB
       THD + Noise  0.03% @ 20 Hz to 20 kHz at maximum output
       S/N  >90 dB, at maximum output (15 dBu), balanced (unweighted)
       Stereo channel separation  >80 dB @ 1 kHz to 20 kHz
    Audio input
       Number/signal type  1 PC level stereo, unbalanced
       Connectors  (1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (ground)
       Impedance  >10k ohms, DC coupled
       Nominal level  -10 dBV (316 mVrms)
       Maximum level  +7 dBV (unbalanced)
        NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
    Audio output
       Number/signal type  1 stereo (2 channel), balanced/unbalanced
       Connectors  (1) 3.5 mm captive screw connector, 5 pole
       Impedance  50 ohms unbalanced, 100 ohms balanced
       Gain error  ¡¾0.1 dB channel to channel
       Maximum level (600 ohm)  >+15 dBu, balanced
    Control/remote — external device (pass-through, unidirectional or bidirectional)
       Serial control port input/output 
          Transmitter  RS-232 via (1) 3.5 mm, 5 pole captive screw connector for RS-232 control (¡¾5 V) (connector is shared with IR control port)
          Receiver  1 set of proprietary signals on a female RJ-45 jack
       Serial control port output/input 
          Transmitter  1 set of proprietary signals on a female RJ-45 jack
          Receiver  RS-232 via a 3.5 mm, 3 pole captive screw connector
       Baud rates  Up to 115200 baud
       Protocol  Data bits = 5 - 8
    Stop bits = 1 or 2
    Parity = odd, even, none
    Flow control = XON, XOFF, none
       Serial control pin configuration  1 = Tx, 2 = Rx, 3 = GND
       IR control port  (1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port)
    TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz
       IR control pin configuration  3 = GND, 4 = IR Tx, 5 = IR Rx
    General
       Power supply  External
    Input: 100-240 VAC, 50-60 Hz
    Output: 12 VDC, 1 A, 12 watts
       Power consumption  7.6 watts, 12 VDC, total, for both transmitter and receiver
        NOTE     Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable.
       Temperature/humidity  Storage: -40 to +158 ¡ÆF (-40 to +70 ¡ÆC) / 10% to 90%, noncondensing
    Operating: +32 to +122 ¡ÆF (0 to +50 ¡ÆC) / 10% to 90%, noncondensing
       Cooling  Convection, no vents
       Mounting
          Rack mount  Yes, with optional 1U high rack shelf
          Furniture mount  Yes, with optional under-desk mounting kit
       Enclosure type  Metal
       Enclosure dimensions 
          Transmitter  1.0" H x 4.3" W x 3.0" D (quarter rack wide)
    (2.5 cm H x 10.9 cm W x 7.6 cm D)
    (Depth excludes connectors.)
          Receiver  1.0" H x 4.3" W x 6.0" D (quarter rack wide)
    (2.5 cm H x 10.9 cm W x 15.2 cm D)
    (Depth excludes connectors.)
       Product weight 
          Transmitter  0.5 lbs (0.3 kg)
          Receiver  1.0 lb (0.5 kg)
       Shipping weight  3 lbs (2 kg)
       Vibration  ISTA 1A in carton (International Safe Transit Association)
       Regulatory compliance 
          Safety  CE, c-UL, UL
          EMI/EMC  CE**, C-tick, FCC Class A**, ICES, VCCI

    Product Diagram 
  •