MTP/HDMI U T A D |
NOTE |
*Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output. | |
|
Video |
MTP analog input |
|
Gain |
Unity |
Maximum resolution, analog |
Up to 2048x1080 or 1080p @ 60 Hz |
Signal transmission distance, analog |
|
HDMI digital input |
|
Maximum data rate |
6.75 Gbps (2.25 Gbps per color) |
Maximum pixel clock |
225 MHz |
Maximum resolution, digital |
Up to 1920x1200 or 1080p @ 60 Hz |
Signal transmission distance, digital |
|
NOTE |
The transmission distance varies greatly depending on the signal resolution and on the type of cable, graphics card, and display used in the system. | |
Formats |
RGB and YCbCr digital video |
Standards |
DVI 1.0, HDMI 1.3 |
|
Video input and loop through |
Number/signal type |
|
MTP input |
1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video input 1 component video (YUV bi-level or tri-level sync) 1 S-video 1 composite video 1 buffered RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video loop through |
HDMI input |
1 single link HDMI (or DVI-D*) |
Connectors |
|
HDMI input |
1 female HDMI type A |
Minimum/maximum levels |
For analog input: 0.3 V to 1.45 Vp-p |
Impedance |
For analog input: 75 ohms |
Horizontal frequency |
For analog input: 15 kHz to 130 kHz |
Vertical frequency |
For analog input: 30 Hz to 150 Hz |
|
Video output |
Number/signal type |
|
MTP output |
1 set of proprietary analog signals |
HDMI digital output |
1 set of proprietary digital signals |
Connectors |
|
MTP output |
1 female RJ-45 |
HDMI digital output |
2 female RJ-45 |
|
Sync — analog inputs |
Input type |
RGBHV, RGBS, RGsB, RsGsBs |
Standards |
NTSC 3.58, NTSC 4.43, PAL, SECAM |
Input level |
3.5 V to 5.5 Vp-p, unterminated |
Input impedance |
573 ohms ¡¾5% |
Max. input voltage |
5.5 V p-p |
Polarity |
Positive or negative (follows input polarity) |
|
Audio |
Gain |
Unbalanced output: 0 dB; balanced output: +6 dB |
MTP input |
|
Frequency response |
20 Hz to 20 kHz, ¡¾1 dB |
THD + Noise |
0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level |
S/N |
>70 dB at maximum output (unweighted) |
HDMI input |
|
Frequency response |
20 Hz to 20 kHz, ¡¾0.06 dB |
THD + Noise |
0.18% @ 1 kHz at nominal level |
S/N |
>76 dB at maximum output (unweighted) |
Stereo channel separation |
>63 dB @ 1 kHz |
|
Audio input |
MTP input |
|
Number/signal type |
2 stereo, unbalanced |
Connectors |
(1) 3.5 mm mini stereo jack 1 pair female RCA |
Impedance |
>10k ohms, unbalanced |
Nominal level |
+4 dBu (1.23 Vrms), -10 dBV (316 mVrms) |
Maximum level |
+18 dBu, (unbalanced) at 1%THD+N |
HDMI input |
|
Number/signal type |
1 stereo, unbalanced |
Connectors |
1 pair female RCA jacks (tip, ring) |
Impedance |
>10k ohms unbalanced, DC coupled |
Nominal level |
-10 dBV (316 mVrms) |
Maximum level |
+6.3 dBu, unbalanced at 1% THD+N |
NOTE |
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu | |
|
Audio output |
MTP output |
From MTP input – see audio input specifications for the MTP receiver |
Number/signal type |
1 set of proprietary analog signals |
Connectors |
1 female RJ-45 |
HDMI output |
From HDMI input – see audio input specs for the HDMI receiver |
Number/signal type |
1 stereo, balanced/unbalanced |
Connectors |
(1) 3.5 mm captive screw connector, 5 pole |
Impedance |
50 ohms unbalanced, 100 ohms balanced |
Maximum level (Hi-Z) |
>11.4 dBu, balanced or unbalanced at 1% THD+N |
Maximum level (600 ohm) |
>5.1 dBm, balanced or unbalanced at 1% THD+N |
|
Control/remote — external device (pass-through, unidirectional or bidirectional) , from HDMI input |
Serial control port input |
RS-232 via (1) 3.5 mm, 3 pole captive screw connector |
Serial control port output |
1 set of proprietary signals on a female RJ-45 jack |
NOTE |
Protocol is mirrored between the transmitter and the receiver. | |
Serial control pin configuration |
Captive screw connector: 1 = Tx, 2 = Rx, 3 = GND |
|
General |
Recommended cable type |
Shielded or unshielded |
MTP output |
CAT 5/5e/6 |
HDMI digital output |
CAT 5/5e/6, Extron DTP26 |
Power input requirements |
12 VDC, 0.5 A for MTP U T A D 12 VDC, 0.2 A for HDMI 201 A D |
Enclosure dimensions |
|
Faceplates |
Three [2.6" H* x 1.3" W x 0.2" D (6.6 cm H* x 3.3 cm W x 0.6 cm D)] (Fits the openings in a 3 gang Decora¢ç faceplate.) *Height is 4.1" [10.4 cm] including mounting tabs. |
Device |
|
MTP |
Two [2.7" H x 3.2" W x 1.5" D (6.9 cm H x 8.1 cm W x 3.8 cm D)] (Depth excludes input connectors.) |
HDMI |
One [2.7" H x 1.8" W x 1.25" D (6.9 cm H x 4.6 cm W x 6.4 cm D)] (Depth excludes input connectors.) |
Product weight |
0.9 lbs (0.4 kg) |
Regulatory compliance |
|
Safety |
CE, c-UL, UL |
EMI/EMC |
CE**, C-tick, FCC Class A**, ICES, VCCI |
NOTE |
**For the HDMI digital link, CE and FCC testing is conducted with STP (shielded twisted pair) cable. | |
MTBF |
30,000 hours |
Warranty |
3 years parts and labor |