| DMS 1600 Series |
|
| Video — DMS DVI boards |
| Routing |
From 4 x 4 to 16 x 16 matrix, expandable by increments of 4 inputs and 4 outputs |
| Gain |
Unity |
| Resolution range |
Up to 1080p (HDTV) or 1920x1200 (the highest resolution of the single link DVI standard) @ 48, 50, or 60 Hz |
| Signal type |
Single-link DVI digital video signals are supported. |
| NOTE |
The DMS DVI Series boards are not compatible with HDMI 1.3. | |
| Digital audio |
Not supported |
| Consumer Electronics Control (CEC) |
Not supported |
| EDID and DDC |
Supports Extended Display Identification Data (EDID) and Display Data Channel (DDC) data using DVI and HDMI standards. EDID and DDC signals are actively buffered. |
| HDCP |
Not supported |
| HPD |
Supports hot plug detection (HPD) of display as a pass-through signal. |
| Maximum data rate |
4.95 Gbps (1.65 Gbps per color) |
| Maximum pixel clock |
165 MHz |
| Standards |
DVI 1.0 |
|
| Video input — DMS 44 DVI and DMS 4i DVI input boards |
| Number/signal type |
4 digital RGB single link DVI-D per input board |
| Connectors |
4 female DVI-I (digital only) per input board |
| Equalization |
Automatic |
| Input cable length |
50' (15.24 m) at 1920x1200 @ 48, 50, or 60 Hz; or 1080p |
| NOTE |
The transmission distance varies depending on the signal resolution and on the type of cable, graphics card, and display used in the system. | |
|
| Video output — DMS 44 DVI and DMS 4o DVI output boards |
| Number/signal type |
4 digital RGB single link DVI-D per output board |
| Connectors |
4 female DVI-I (digital only) per output board |
| Re-clocking |
Automatic |
| Output cable length |
50' (15.24 m) at 1920x1200 @ 48, 50, or 60 Hz; or 1080p |
| Peripheral device power |
250 mA per output |
|
| Control/remote — switcher host ports |
| Serial host control port |
1 bidirectional RS-232 or RS-422, rear panel 9-pin female D connector |
| Baud rate and protocol |
9600 (default), 19200, 38400, 115200 baud, adjustable; 8 data bits, 1 stop bit, no parity |
| Serial control pin configurations |
| 9-pin female D connector |
|
| RS-232 |
2 = Tx, 3 = Rx, 5 = GND |
| RS-422 |
2 = Tx-, 3 = Rx-, 5 = GND, 7 = Rx+, 8 = Tx+ |
| USB control ports |
1 front panel female mini USB B |
| USB standards |
USB 2.0, low speed |
| Ethernet control port |
1 RJ-45 female |
| Ethernet data rate (for network communication) |
10/100Base-T, half/full duplex with autodetect |
| Ethernet protocol |
ARP, ICMP (ping), IP, TCP, DHCP, HTTP, SMTP, Telnet |
| Ethernet default settings |
Link speed and duplex level = autodetected
IP address = 192.168.254.254
Subnet mask = 255.255.0.0
Default gateway = 0.0.0.0
DHCP = off |
| Web server |
Up to 200 simultaneous sessions
7.0 MB nonvolatile user memory |
| Program control |
Extron control/configuration program for Windows®
Extron Simple Instruction Set™ (SIS™)
Microsoft® Internet Explorer® ver. 6 or higher, Telnet |
|
| General |
| Power |
1 or 2 (positive-negative), 100 VAC to 240 VAC, 50-60 Hz; internal, 175 watts each
*A redundant power supply is optional. |
| With primary power supply only |
Enclosure without boards: 29 watts at 115 VAC, 60 Hz
Enclosure fully loaded with (4) 4x4 I/O boards: 101 watts at 115 VAC, 60 Hz |
| With both primary and redundant power supplies |
Enclosure without boards: 36 watts at 115 VAC, 60 Hz
Enclosure fully loaded with (4) 4x4 I/O boards: 108 watts at 115 VAC, 60 Hz |
| Individual I/O boards |
Each 4x4 I/O board: 18 watts at 115 VAC, 60 Hz
Each 4 input board: 9 watts at 115 VAC, 60 Hz
Each 4 output board: 9 watts at 115 VAC, 60 Hz |
| Temperature/humidity |
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling |
Fan, right to left (as viewed from front panel) |
| Thermal dissipation, full load |
|
| With primary power supply only |
86.1 BTU/hr |
| With both primary and redundant power supplies |
92.1 BTU/hr |
| Rack mount |
Yes |
| Enclosure type |
Metal |
| Enclosure dimensions |
7.0" H x 17.0" W x 12" D (4U high, full rack wide)
(17.8 cm H x 43.2 cm W x 30.5 cm D)
(Depth excludes connectors and buttons. Width excludes rack ears.) |
| Product weight with boards installed |
|
| With primary power supply only |
26.9 lbs (12.2 kg) |
| With both primary and redundant power supplies |
27.9 lbs (12.6 kg) |
| Shipping weight with boards installed |
32 lbs (15 kg) |
| DIM weight, international |
32 lbs (15 kg) |
| Vibration |
ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance |
|
| Safety |
CE, c-UL, UL |
| EMI/EMC |
CE, C-tick, FCC Class A, ICES, VCCI |
| MTBF |
30,000 hours |
| Warranty |
3 years parts and labor |
