| FOXBOX 4G Tx VGA MM |
Multimode - Transmitter |
60-934-11 |
|
|
|
|
|
FOXBOX 4G Rx VGA MM |
Multimode - Receiver |
60-934-21 |
|
|
|
|
|
FOXBOX 4G Tx VGA SM |
Singlemode - Transmitter |
60-934-12 |
|
|
|
|
|
FOXBOX 4G Rx VGA SM |
Singlemode - Receiver |
60-934-22 |
FOXBOX 4G VGA Series |
| NOTE |
These transceivers are class 1 laser products. They meet the safety regulations of IEC-60825, FDA 21 CFR 1040.10, and FDA 21 CFR 1040.11. | |
|
| Optical fiber interconnection between transmitter and receiver |
| Number/type |
1 or 2 fiber optic |
| Connectors |
2 LC connectors |
| Operating distance |
|
| Singlemode |
30 km (18.75 miles) with singlemode (SM) cables with a FOXBOX 4G SM |
| Multimode |
300 m (985') with 62.5 µm multimode (MM) cables with a FOXBOX 4G MM
1 km (3280') with 50 µm multimode (MM) cables with a FOXBOX 4G MM
2 km (6561') with 50 µm 2000 MHz bandwidth laser optimized multimode cable with a FOXBOX 4G MM |
| NOTE |
Operating distance is approximate. These are typical maximum distances that may vary depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks. | |
| Nominal peak wavelength |
850 nm for FOXBOX 4G MM, 1310 nm for FOXBOX 4G SM |
| Data rate |
4.25 Gbps |
| Transmission power |
|
| Singlemode |
-5 dBm, typical |
| Multimode |
-5 dBm, typical |
| Maximum receiver sensitivity |
|
| Singlemode |
-18 dBm, typical |
| Multimode |
-12 dBm, typical |
| Optical loss budget |
|
| Singlemode |
13 dB, maximum |
| Multimode |
7 dB, maximum |
|
| Video |
| Signal type |
VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs |
| Gain |
Unity |
| Pixel data bit depth |
8 bits per channel, 3 channels (R, G, B; or YUV) |
| Maximum resolution |
1600x1200 or 1080p @ 60 Hz, digitized pixel for pixel; higher resolutions up to 2048x1120, undersampled |
|
| Video input |
| Number/signal type |
1 VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs |
| Connectors |
1 female 15-pin HD |
| Nominal level |
1 Vp-p for Y of component video
0.7 Vp-p for RGB and for R-Y and B-Y of component video |
| Minimum/maximum levels |
Analog: 0.3 V to 0.75 Vp-p with no offset, terminated |
| Impedance |
75 ohms |
| Horizontal frequency |
24 kHz to 100 kHz |
| Vertical frequency |
40 Hz to 120 Hz |
| Return loss |
<-40 dB @ 5 MHz |
|
| Video output |
| Number/signal type |
With input from a FOXBOX 4G Tx VGA or a FOX 500 Tx:
1 VGA-UXGA RGBHV, RGsB (follows input or can be set by user)
With input from a FOXBOX 4G Tx VGA/YUV:
1 VGA-UXGA RGBHV, RGBS, component video (bi- or tri-level YUV, 480p, 576p, 720p, 1080i, 1080p) |
| Connectors |
1 female 15-pin HD |
| Nominal level |
1 Vp-p for Y of component video
0.7 Vp-p for RGB and for R-Y and B-Y of component video |
| Minimum/maximum levels |
0.3 V to 0.75 Vp-p, terminated |
| Impedance |
75 ohms |
| Return loss |
-30 dB @ 5 MHz |
| DC offset |
±5 mV with input at 0 offset |
| Video delay |
1-2 frames |
|
| Sync |
| Input type |
RGBHV, RGBS, RGsB, RsGsBs |
| Output type |
RGBHV, RGsB (follows input or can be set by user) |
| Input level |
2.5 V to 5.0 Vp-p |
| Output level |
TTL: 5.0 Vp-p, unterminated, on HV, for RGBHV, RGBS
0.3 Vp-p for component video (bi-level sync, unterminated) or for Gs (SOG), terminated
0.6 Vp-p for component video (tri-level sync) |
| Input impedance |
10k ohms |
| Output impedance |
75 ohms |
| Polarity |
Positive or negative (follows input or can be set by user) |
|
| Audio |
| Gain |
|
| Range |
Adjustable, -18 dB to +10 dB |
| Default |
Unbalanced output: 0 dB |
| Frequency response |
20 Hz to 20 kHz, ±0.5 dB |
| THD + Noise |
0.10% @ 1 kHz at nominal level |
| S/N |
>80 dB at maximum output (unweighted) |
| CMRR |
65 dB @ 20 Hz to 20 kHz |
| Audio bits per sample |
18 bits per channel, 2 channels (L, R) |
| Sampling rate |
48 kHz |
|
| Audio input — transmitters (Tx units) |
| Number/signal type |
1 unbalanced stereo or 2 unbalanced mono |
| Connectors |
(1) 3.5 mm mini stereo jack |
| Impedance |
18k ohms unbalanced, DC coupled |
| Nominal level |
-10 dBV (316 mVrms) |
| Maximum level |
+8.9 dBV, (unbalanced) at 1% THD+N |
| NOTE |
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu | |
|
| Audio output — receivers (Rx units) |
| Number/signal type |
1 unbalanced stereo or 2 unbalanced mono |
| Connectors |
(1) 3.5 mm mini stereo jack |
| Impedance |
50 ohms unbalanced |
| Nominal level |
-10 dBV (316 mVrms) |
| Maximum level (Hi-Z) |
+7.6 dBu, unbalanced at 1% THD+N |
| Maximum level (600 ohm) |
>+6.3 dBu, unbalanced at 1% THD+N |
| Audio delay |
1.5 frames |
|
| Control/remote |
| Serial control ports on each unit (transmitter and receiver) |
| Control |
1 RS-232, 2.5 mm mini stereo jack (front panel) |
| Pass-through |
1 RS-232, 3.5 mm captive screw connector, 5 pole (3 pins are used) (rear panel) |
| Baud rate and protocol |
|
| Control |
9600 baud, 8 data bits, 1 stop bit, no parity |
| Pass-through |
9600 to 115,200 baud |
| Program control |
Extron control/configuration program for Windows®
Extron Simple Instruction Set™ (SIS™) |
|
| General |
| External power supply |
100 VAC to 240 VAC, 50-60 Hz, external; to 12 VDC, 1 A, regulated |
| Power input requirements |
12 VDC, 0.6 A |
| Temperature/humidity |
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling |
Convection, vents on top and side panels |
| Thermal dissipation |
|
| Transmitter |
|
| 115 VAC, 60 Hz |
7.8 BTU/hr |
| 240 VAC, 50 Hz |
11.4 BTU/hr |
| Receiver |
|
| 115 VAC, 60 Hz |
8.0 BTU/hr |
| 240 VAC, 50 Hz |
10.9 BTU/hr |
| Mounting |
|
| Rack mount |
Yes, with optional rack shelf |
| Furniture mount |
Yes, with optional under desk mounting kit |
| Enclosure type |
Metal |
| Enclosure dimensions |
1.0" H x 4.3" W x 6.0" D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 15.2 cm D)
(Depth excludes connectors.) |
| Product weight |
0.7 lbs (0.3 kg) per unit, 1.4 lbs (0.6 kg) per pair |
| Shipping weight |
3 lbs (2 kg) per unit, 6 lbs (3 kg) per pair |
| Vibration |
ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance |
|
| Safety |
CE, c-UL, FDA Class 1, UL |
| EMI/EMC |
CE, C-tick, FCC Class A, ICES, VCCI |
| MTBF |
30,000 hours |
| Warranty |
3 years parts and labor |
