MTP 15HD A Series |
|
Video |
Gain |
Unity |
Number/signal type |
1 set of proprietary analog signals |
Connectors |
|
MTP R 15HD RSA D |
1 female RJ-45 on a pigtail |
All other models |
1 female RJ-45 |
|
Video input and loop through — transmitters |
Number/signal type |
|
MTP T 15HD A |
1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video 1 buffered RGBHV, RGBS, RGsB, RsGsBs local monitor loop through (includes ID bits) |
MTP T 15HD A AAP, MTP T 15HD A D, MTP T 15HD A WM |
1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video |
Connectors |
|
MTP T 15HD A |
2 female 15-pin HD |
All other transmitters |
1 female 15-pin HD |
Nominal level |
1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video |
Minimum/maximum levels |
0.3 V to 1.45 Vp-p |
Impedance |
75 ohms |
Horizontal frequency |
15 kHz to 130 kHz |
Vertical frequency |
30 Hz to 150 Hz |
Return loss |
<-30 dB @ 5 MHz |
DC offset (max. allowable) |
250 mV |
|
Video output — receivers (MTP RL 15HD A, MTP RL 15HD A SEQ, MTP R 15HD RSA D) |
Number/signal type |
|
MTP R 15HD RSA D |
1 analog VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs, HD component video, component video, S-video, or composite video |
All other receivers |
1 set of proprietary analog signals 1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video |
Connectors |
|
MTP R 15HD RSA D |
1 female 15-pin HD |
All other receivers |
1 female RJ-45 1 female 15-pin HD |
Nominal level |
1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video |
Minimum/maximum levels |
0.3 V to 1.45 Vp-p |
Impedance |
75 ohms |
Return loss |
<-30 dB @ 5 MHz |
DC offset |
|
MTP R 15HD RSA D |
<¡¾20 mV with input at 0 offset |
All other receivers |
<¡¾35 mV with input at 0 offset |
Maximum resolution |
1920x1200 or 2048x1080 |
NOTE |
Refer to the user's manual for the maximum distances recommended for specific resolutions. | |
|
Sync |
Input type (transmitters) |
RGBHV, RGBS, RGsB, RsGsBs |
Output type (receivers) |
RGBHV, RGBS, RGsB, RsGsBs |
Standards |
NTSC 3.58, NTSC 4.43, PAL, SECAM |
Input level (transmitter) |
3.5 V to 5.5 Vp-p, unterminated |
Output level (receivers) |
4.0 V to 5.0 Vp-p, unterminated |
Input impedance (transmitter) |
573 ohms ¡¾5% |
Output impedance (receivers) |
110 ohms |
Max. input voltage (transmitter) |
5.5 V p-p |
Polarity |
|
Transmitter |
Positive or negative (follows input polarity) |
Receivers |
Positive or negative (switch-selectable) |
|
Audio — all models |
Number/signal type |
1 set of proprietary analog signals |
Connectors |
1 female RJ-45 |
Gain |
Unbalanced output: 0 dB; balanced output: +6 dB |
Frequency response |
20 Hz to 20 kHz, ¡¾1 dB |
THD + Noise |
0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level |
S/N |
>70 dB at maximum output (unweighted) |
Stereo channel separation |
|
MTP T 15HD A AAP, MTP T 15HD A D, MTP T 15HD A WM |
>60 dB @ 1 kHz |
CMRR |
>43 dB @ 20 Hz to 20 kHz |
|
Audio input — transmitters |
Number/signal type |
1 stereo, unbalanced |
Connectors |
(1) 3.5 mm mini stereo jack |
Impedance |
>10k ohms, unbalanced |
Nominal level |
+4 dBu (1.23 Vrms), -10 dBV (316 mVrms) |
Maximum level |
+18 dBu, (unbalanced) at 1%THD+N |
NOTE |
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu | |
|
Audio output — MTP T 15HD A AAP, MTP T 15HD A D, MTP T 15HD A WM local stereo output |
Number/signal type |
1 stereo, balanced/unbalanced |
Connectors |
(1) 3.5 mm direct insertion captive screw connector, 5 pole |
Impedance |
50 ohms unbalanced, 100 ohms balanced |
Gain error |
¡¾1 dB channel to channel |
Maximum level (Hi-Z) |
>+23 dBu, balanced or unbalanced at 1% THD+N |
Maximum level (600 ohm) |
>+17 dBm, balanced or unbalanced at 1% THD+N |
|
Audio output — receivers |
Number/signal type |
|
MTP R 15HD RSA D |
1 mono, balanced/unbalanced |
All other receivers |
2 mono, balanced/unbalanced |
Connectors |
|
MTP R 15HD RSA D |
(1) 3.5 mm captive screw connector, 5 pole (uses 3 poles) |
All other receivers |
(1) 3.5 mm captive screw connector, 5 pole |
Impedance |
50 ohms unbalanced, 100 ohms balanced |
Gain error |
MTP R 15HD RSA D: ¡¾1 dB channel to channel |
Nominal level |
+4 dBu (1.23 Vrms), -10 dBV (316 mVrms) |
Maximum level |
|
MTP R 15HD RSA D |
14 dBm, unbalanced at 1% THD+N |
All other receivers |
+18 dBu, unbalanced at 1% THD+N |
|
Control/remote — external device (pass-through, unidirectional or bidirectional) — MTP R 15HD RSA D only |
Serial control port input/output |
1 set of proprietary signals on a female RJ-45 jack |
Serial control port output/input |
RS-232 via 3 poles of a 3.5 mm captive screw connector, 5 pole |
NOTE |
The serial communications link is unidirectional only, transmitter to receiver, unless the receiver's directional DIP switch has been repositioned. The switch should be repositioned only when the receiver is the only one in the system. | |
Baud rates |
Up to 38400 bps at up to 1000' (304.8 m) (Higher data rates and distances are possible. Performance varies based on baud rate and cable length.) |
Protocol |
Data bits = 5 - 8 Stop bits = 1 or 2 Parity = odd, even, none Flow control = XON, XOFF, none |
NOTE |
Protocol is mirrored between the transmitter and the receiver. | |
Serial control pin configuration |
Captive screw connector: 1 = TX, 2 = RX, 3 = GND |
|
General |
Recommended cable type |
CAT 5/5E/6 (shielded or unshielded) |
External power supply |
100 VAC to 240 VAC, 50-60 Hz, external; to 12 VDC, 1 A, regulated |
Power input requirements |
12 VDC, 0.5 A |
Temperature/humidity |
Storage: -40 to +158 ¡ÆF (-40 to +70 ¡ÆC) / 10% to 90%, noncondensing Operating: +32 to +122 ¡ÆF (0 to +50 ¡ÆC) / 10% to 90%, noncondensing |
Cooling |
Convection, no vents |
Mounting |
|
Rack mount |
|
MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ |
Yes, with optional rack shelf mounting kit |
Furniture mount |
|
MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ |
Yes, with optional under-desk mounting kit |
MTP T 15HD A AAP |
Wall or furniture mountable with optional AAP mounting faceplates that have double space high AAP opening |
MTP T 15HD A D, MTP R 15HD RSA D |
Wall or furniture mountable in a Decora¢ç-style opening with a standard electrical wall box or Decora size mud ring |
MTP T 15HD A WM |
Wall or furniture mountable in a 1-gang opening |
Pole mount |
|
MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ |
Yes, with optional pole mounting kit |
Enclosure type |
Metal |
Enclosure dimensions |
|
MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ |
1.7" H x 4.3" W x 3.0" D (1U high, quarter rack wide) 4.3 cm H x 10.9 cm W x 7.6 cm D (Depth excludes connectors.) |
Faceplates |
|
MTP T 15HD A AAP |
1.4" H x 3.5" W x 0.1" D (3.6 cm H x 8.9 cm W x 0.3 cm D) (double space high AAP plate) |
MTP T 15HD A D, MTP R 15HD RSA D |
2.6" H* x 1.3" W x 0.1" D (6.6 cm H* x 3.3 cm W x 0.3 cm D) (Fits the opening in a 1 gang, 4.4" H x 2.7" W Decora-style wallplate. Depth excludes connectors.) *Overall height is 4.1" (10.4 cm) including mounting tabs. |
MTP T 15HD A WM |
4.5" H x 2.8" W x 0.1" D (11.4 cm H x 7.1 cm W x 0.3 cm D) (1 gang) |
Device |
|
MTP R 15HD RSA D |
2.75" H x 1.65" W x 1.3" D (7.0 cm H x 4.2 cm W x 3.3 cm D) (Depth excludes connectors.) |
Other AAP, D, and WM models |
2.7" H x 1.4" W x 1.4" D (6.9 cm H x 3.6 cm W x 3.6 cm D) (Depth excludes connectors.) |
Product weight |
0.4 lbs (0.2 kg) |
Shipping weight |
2 lbs (1 kg) |
Vibration |
ISTA 1A in carton (International Safe Transit Association) |
Regulatory compliance |
|
Safety |
CE, c-UL, UL |
EMI/EMC |
CE, C-tick, FCC Class A, ICES, VCCI |
MTBF |
30,000 hours |
Warranty |
3 years parts and labor |