Video |
Gain |
Unity |
Bandwidth |
|
Composite video 4, 6, and 8 input models |
300 MHz (-3 dB) |
S-video models and composite video 12 input models |
250 MHz (-3 dB) |
Crosstalk |
<-60 dB @ 5 MHz |
Switching speed |
<20 ms (max.) |
|
Video input |
Number/signal type |
|
SW 6/8/12V, SW 4/6/8/12AV/AV RCA, SW 6/8/12A/A RCA |
4, 6, 8, or 12 (depending on the model) composite video |
SW 6/8/12 SV, SW 4/6/8/12SVA/SVA RCA |
4, 6, 8, or 12 (depending on the model) S-video |
Connectors |
|
SW 6/8/12V, SW 4/6/8/12AV/AV RCA, SW 6/8/12A/A RCA |
4, 6, 8, or 12 (depending on the model) female BNC |
SW 6/8/12 SV, SW 4/6/8/12SVA/SVA RCA |
4, 6, 8, or 12 (depending on the model) female 4-pin mini DIN |
Nominal level |
1 Vp-p for Y of S-video, and for composite video 0.3 Vp-p for C of S-video |
Minimum/maximum levels |
0.4 V to 2.0 Vp-p with no offset |
Impedance |
75 ohms |
Return loss |
<-29 dB @ 0 to 10 MHz |
DC offset (max. allowable) |
5.0 V |
|
Video output |
Number/signal type |
|
Composite video models |
2 buffered composite video |
S-video models |
1 buffered S-video, 1 buffered composite video |
Connectors |
|
Composite video models |
2 female BNC |
S-video models |
1 female BNC, 1 female 4-pin mini DIN |
Nominal level |
1 Vp-p for Y of S-video, and for composite video 0.3 Vp-p for C of S-video |
Minimum/maximum levels |
0.4 V to 2.0 Vp-p (follows input) |
Impedance |
75 ohms |
Return loss |
-30 dB @ 5 MHz |
DC offset |
¡¾5 mV with input at 0 offset |
Switching type |
Vertical interval switching |
|
Sync |
Genlock connectors |
2 female BNC (1 input, 1 loop-through) |
Standards |
NTSC 3.58, NTSC 4.43, PAL, SECAM |
|
Audio |
Gain |
Adjustable. When gain is set to unity (0 dB), balanced output from captive screw connectors or unbalanced output from RCA connectors has a 0 dB gain; unbalanced output from captive screw connectors is attenuated by 6 dB. |
Frequency response |
20 Hz to 20 kHz, ¡¾0.5 dB |
THD + Noise |
<0.04% @ 1 kHz at nominal level |
S/N |
>90 dB at maximum output (unweighted) |
|
Audio input |
Number/signal type |
|
SW 4/6/8/12AV, SW 4/6/8/12SVA, SW 6/8/12A |
4, 6, 8, or 12 (depending on the model) stereo, balanced/unbalanced |
SW 4/6/8/12AV RCA, SW 4/6/8/12SVA RCA, SW 6/8/12A RCA |
4, 6, 8, or 12 (depending on the model) stereo, unbalanced |
Connectors |
|
SW 4/6/8/12AV, SW 4/6/8/12SVA, SW 6/8/12A |
4, 6, 8, or 12 (depending on the model) 3.5 mm captive screw connectors, 5 pole |
SW 4/6/8/12AV RCA, SW 4/6/8/12SVA RCA, SW 6/8/12A RCA |
8, 12, 16, or 24 (depending on the model) female RCA |
Impedance |
|
RCA models |
12k ohms unbalanced, DC coupled |
All other models |
25k ohms unbalanced, 50k ohms balanced, DC coupled |
Nominal level |
+4 dBu (1.23 Vrms), -10 dBV (316 mVrms), configurable |
Maximum level |
>+15 dBu, (balanced or unbalanced) at 1% THD+N |
Input gain adjustment |
–18 dB to +24 dB, adjustable per input |
NOTE |
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu. | |
|
Audio output |
Number/signal type |
|
SW 4/6/8/12AV, SW 4/6/8/12SVA, SW 6/8/12A |
2 stereo, balanced/unbalanced |
SW 4/6/8/12AV RCA, SW 4/6/8/12SVA RCA, SW 6/8/12A RCA |
1 stereo, unbalanced |
Connectors |
|
SW 4/6/8/12AV, SW 4/6/8/12SVA, SW 6/8/12A |
(2) 3.5 mm captive screw connectors, 5 pole |
SW 4/6/8/12AV RCA, SW 4/6/8/12SVA RCA, SW 6/8/12A RCA |
2 female RCA (1) 3.5 mm captive screw connector, 5 pole |
Impedance |
50 ohms unbalanced, 100 ohms balanced |
Gain error |
¡¾0.1 dB channel to channel |
Nominal level |
+4 dBu (1.23 Vrms), -10 dBV (316 mVrms), configurable |
Maximum level (Hi-Z) |
>26 dBu, balanced; >+20 dBu, unbalanced at 1% THD+N |
Maximum level (600 ohm) |
>21 dBm, balanced; >+15 dBm, unbalanced at 1% THD+N |
|
Control/remote — switcher |
Serial control port |
RS-232, female 9-pin D connector (also used for contact closure for 4- and 6-input models) |
Baud rate and protocol |
9600 baud, 8 data bits, 1 stop bit, no parity |
Serial control pin configuration |
2 = TX, 3 = RX, 5 = GND |
Contact closure |
|
SW 4/6 ___ |
1 female 9-pin D connector (also used for RS-232) |
Contact closure pin configuration |
|
SW 4/6 ___ models only |
1 = input 1, 4 = input 2, 5 = GND, 6 = input 3, 7 = input 4, 8 = input 5, 9 = input 6 |
IR controller module |
Extron IR 102 kit (optional) |
Program control |
Extron control/configuration program for Windows¢ç Extron Simple Instruction Set (SIS¢â) |
|
General |
Power |
100 VAC to 240 VAC, 50-60 Hz, 20 watts, internal |
Temperature/humidity |
Storage: -40 to +158 ¡ÆF (-40 to +70 ¡ÆC) / 10% to 90%, noncondensing Operating: +32 to +122 ¡ÆF (0 to +50 ¡ÆC) / 10% to 90%, noncondensing |
Cooling |
Convection, no vents |
Mounting |
|
Rack mount |
Yes, with included rack mounting kit |
Furniture mount |
Yes, with optional under-desk mounting kit |
Enclosure type |
Metal |
Enclosure dimensions |
1.75" H x 17.4" W x 8.5" D (1U high, full rack wide) 4.4 cm H x 44.2 cm W x 21.6 cm D (Depth excludes connectors.) |
Product weight |
7.0 lbs (3.2 kg) |
Shipping weight |
10 lbs (5 kg) |
Vibration |
ISTA 1A in carton (International Safe Transit Association) |
Regulatory compliance |
|
Safety |
CE, c-UL, UL |
EMI/EMC |
CE, C-tick, FCC Class A, ICES, VCCI |
MTBF |
30,000 hours |
Warranty |
3 years parts and labor |