| MTP 15HD A Series |
|
| Video |
| Gain |
Unity |
| Number/signal type |
1 set of proprietary analog signals |
| Connectors |
1 female RJ-45 |
|
| Video input and loop through — transmitters |
| Number/signal type |
|
| MTP T 15HD A |
1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video
1 buffered RGBHV, RGBS, RGsB, RsGsBs local monitor loop through (includes ID bits) |
| MTP T 15HD A AAP, MTP T 15HD A D, MTP T 15HD A WM |
1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video |
| Connectors |
|
| MTP T 15HD A |
2 female 15-pin HD |
| MTP T 15HD A AAP, MTP T 15HD A D, MTP T 15HD A WM |
1 female 15-pin HD |
| Nominal level |
1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video |
| Minimum/maximum levels |
0.3 V to 1.45 Vp-p |
| Impedance |
75 ohms |
| Horizontal frequency |
15 kHz to 130 kHz |
| Vertical frequency |
30 Hz to 150 Hz |
| Return loss |
<-30 dB @ 5 MHz |
| DC offset (max. allowable) |
250 mV |
|
| Video output — receivers (MTP RL 15HD A, MTP RL 15HD A SEQ) |
| Number/signal type |
1 set of proprietary analog signals
1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video |
| Connectors |
1 female RJ-45
1 female 15-pin HD |
| Nominal level |
1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video |
| Minimum/maximum levels |
0.3 V to 1.45 Vp-p |
| Impedance |
75 ohms |
| Return loss |
<-30 dB @ 5 MHz |
| DC offset |
<±35 mV with input at 0 offset |
| Maximum resolution |
1920x1200 |
|
|
| Sync |
| Input type (transmitters) |
RGBHV, RGBS, RGsB, RsGsBs |
| Output type (receivers) |
RGBHV, RGBS, RGsB, RsGsBs |
| Standards |
NTSC 3.58, NTSC 4.43, PAL, SECAM |
| Input level (transmitter) |
3.5 V to 5.5 Vp-p, unterminated |
| Output level (receivers) |
4.0 V to 5.0 Vp-p, unterminated |
| Input impedance (transmitter) |
573 ohms ±5% |
| Output impedance (receivers) |
110 ohms |
| Max. input voltage (transmitter) |
5.5 V p-p |
| Polarity |
|
| Transmitter |
Positive or negative (follows input polarity) |
| Receivers |
Positive or negative (switch-selectable) |
|
| Audio — all models |
| Number/signal type |
1 set of proprietary analog signals |
| Connectors |
1 female RJ-45 |
| Gain |
Unbalanced output: 0 dB; balanced output: +6 dB |
| Frequency response |
20 Hz to 20 kHz, ±1 dB |
| THD + Noise |
0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level |
| S/N |
>70 dB at maximum output (unweighted) |
| Stereo channel separation |
|
| MTP T 15HD A AAP, MTP T 15HD A D, MTP T 15HD A WM |
>60 dB @ 1 kHz |
| CMRR |
>43 dB @ 20 Hz to 20 kHz |
|
| Audio input — transmitters |
| Number/signal type |
1 stereo, unbalanced |
| Connectors |
(1) 3.5 mm mini stereo jack |
| Impedance |
>10k ohms, unbalanced |
| Nominal level |
+4 dBu (1.23 Vrms), -10 dBV (316 mVrms) |
| Maximum level |
+18 dBu, (unbalanced) at 1%THD+N |
|
|
| Audio output — MTP T 15HD A AAP, MTP T 15HD A D, MTP T 15HD A WM local stereo output |
| Number/signal type |
1 stereo, balanced/unbalanced |
| Connectors |
(1) 3.5 mm direct insertion captive screw connector, 5 pole |
| Impedance |
50 ohms unbalanced, 100 ohms balanced |
| Gain error |
±1 dB channel to channel |
| Maximum level (Hi-Z) |
>+23 dBu, balanced or unbalanced at 1% THD+N |
| Maximum level (600 ohm) |
>+17 dBm, balanced or unbalanced at 1% THD+N |
|
| Audio output — receivers |
| Number/signal type |
2 mono, balanced/unbalanced |
| Connectors |
(1) 3.5 mm captive screw connector, 5 pole |
| Impedance |
50 ohms unbalanced, 100 ohms balanced |
| Nominal level |
+4 dBu (1.23 Vrms), -10 dBV (316 mVrms) |
| Maximum level |
+18 dBu, unbalanced at 1% THD+N |
|
| General |
| Recommended cable type |
CAT 5/5E/6 (shielded or unshielded) |
| External power supply |
100 VAC to 240 VAC, 50-60 Hz, external; to 12 VDC, 1 A, regulated |
| Power input requirements |
12 VDC, 0.5 A |
| Temperature/humidity |
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling |
Convection, no vents |
| Mounting |
|
| Rack mount |
|
| MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ |
Yes, with optional rack shelf mounting kit |
| Furniture mount |
|
| MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ |
Yes, with optional under-desk mounting kit |
| MTP T 15HD A AAP |
Wall or furniture mountable with optional AAP mounting faceplates that have double space high AAP opening |
| MTP T 15HD A D |
Wall or furniture mountable in a Decora®-style opening |
| MTP T 15HD A WM |
Wall or furniture mountable in a 1-gang opening |
| Pole mount |
|
| MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ |
Yes, with optional pole mounting kit |
| Enclosure type |
Metal |
| Enclosure dimensions |
|
| MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ |
1.7" H x 4.3" W x 3.0" D (1U high, quarter rack wide)
4.3 cm H x 10.9 cm W x 7.6 cm D
(Depth excludes connectors.) |
| Faceplates |
|
| MTP T 15HD A AAP |
1.4" H x 3.5" W x 0.1" D (3.6 cm H x 8.9 cm W x 0.3 cm D)
(double space high AAP plate) |
| MTP T 15HD A D |
2.6" H* x 1.3" W x 0.1" D (6.6 cm H* x 3.3 cm W x 0.3 cm D)
(Fits the opening in a 1 gang Decora faceplate.)
*Height is 3.8" [9.7 cm] including mounting tabs. |
| MTP T 15HD A WM |
4.5" H x 2.8" W x 0.1" D (11.4 cm H x 7.1 cm W x 0.3 cm D) (1 gang) |
| Device |
|
| AAP, D, and WM models |
2.7" H x 1.4" W x 1.4" D (6.9 cm H x 3.6 cm W x 3.6 cm D)
(Depth excludes connectors.) |
| Product weight |
0.4 lbs (0.2 kg) |
| Shipping weight |
2 lbs (1 kg) |
| Vibration |
ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance |
|
| Safety |
CE, c-UL, UL |
| EMI/EMC |
CE, C-tick, FCC Class A, ICES, VCCI |
| MTBF |
30,000 hours |
| Warranty |
3 years parts and labor |
|
