| MTP 15HD RS Series |
|
| Video |
| Gain |
Unity |
| Number/signal type |
1 set of proprietary analog signals |
| Connectors |
1 female RJ-45 |
|
| Video input and loop-through — transmitter (MTP T 15HD RS) |
| Number/signal type |
1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video
1 buffered RGBHV, RGBS, RGsB, RsGsBs local monitor loop through (includes ID bits) |
| Connectors |
2 female 15-pin HD |
| Nominal level |
1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video |
| Minimum/maximum levels |
0.3 V to 1.45 Vp-p |
| Impedance |
75 ohms |
| Horizontal frequency |
15 kHz to 130 kHz |
| Vertical frequency |
30 Hz to 150 Hz |
| Return loss |
<-30 dB @ 5 MHz |
| DC offset (max. allowable) |
250 mV |
|
| Video output — receivers (MTP RL 15HD RS, MTP RL 15HD RS SEQ) |
| Number/signal type |
1 set of proprietary analog signals
1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video |
| Connectors |
1 female RJ-45
1 female 15-pin HD |
| Nominal level |
1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video |
| Minimum/maximum levels |
0.3 V to 1.45 Vp-p |
| Impedance |
75 ohms |
| Return loss |
<-30 dB @ 5 MHz |
| DC offset |
<±20 mV with input at 0 offset |
| Maximum resolution |
1920x1200 |
|
|
| Sync |
| Input type (transmitter) |
RGBHV, RGBS, RGsB, RsGsBs |
| Output type (receivers) |
RGBHV, RGBS, RGsB, RsGsBs |
| Standards |
NTSC 3.58, NTSC 4.43, PAL, SECAM |
| Input level (transmitter) |
3.5 V to 5.5 Vp-p, unterminated |
| Output level (receivers) |
4.0 V to 5.0 Vp-p, unterminated |
| Input impedance |
510 ohms |
| Output impedance |
110 ohms |
| Max. input voltage |
5.5 Vp-p |
| Polarity |
|
| Transmitter |
Positive or negative (follows input polarity) |
| Receivers |
Positive or negative (switch selectable) |
|
| Control/remote — external device (pass-through, unidirectional or bidirectional) |
| Serial control port input/output |
| MTP T 15HD RS |
RS-232 via (1) 3.5 mm, 3 pole captive screw connector |
| Receivers |
1 set of proprietary signals on a female RJ-45 jack |
| Serial control port output/input |
| MTP T 15HD RS |
1 set of proprietary signals on a female RJ-45 jack |
| Receivers |
RS-232 via a 3.5 mm, 3 pole captive screw connector |
| NOTE |
The serial communications link of an MTP RL 15HD RS or MTP RL 15 HD RS SEQ is unidirectional only, transmitter to receiver, unless the receiver's directional jumper has been repositioned. The jumper should be repositioned only when the receiver is the only one in the system. | |
| Baud rates |
Up to 38400 bps at up to 600' (183 m) (Higher data rates and distances are possible. Performance will vary based on baud rate and cable length.) |
| Protocol |
Data bits = 5 - 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none |
|
| Serial control pin configurations |
Captive screw connectors: 1 = TX, 2 = RX, 3 = GND |
|
| General |
| Recommended cable type |
CAT 5/5E/6 (shielded or unshielded) |
| External power supply |
100 VAC to 240 VAC, 50/60 Hz, external; to 12 VDC, 2 A, regulated |
| Power input requirements |
12 VDC, 0.5 A |
| Temperature/humidity |
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling |
Convection, no vents |
| Mounting |
| Rack mount |
Yes, with optional 1U, 9.5" deep rack shelf (RSU 129, #60-190-01 or RSB 129, #60-604-01); 1U, 6" deep rack shelf (RSU 126, #60-190-10 or RSB 126, #60-604-10); or VersaTools® 1U, 3.5" deep rack shelf (RSF 123, #60-190-20 or RSB 123, 60-604-20) |
| Furniture mount |
Yes, with optional Mini Under-Desk Mounting Kit, part #70-212-01 (MBU 123) |
| Pole mount |
Yes, with optional projector mounting kit, part #70-217-01 (PMK 100) |
| Rack mount |
|
| Enclosure type |
Metal |
| Enclosure dimensions |
1.7" H x 4.3" W x 3.0" D (1U high, quarter rack wide)
(4.3 cm H x 10.9 cm W x 7.6 cm D)
(Depth excludes connectors.) |
| Product weight |
0.4 lbs (0.2 kg) |
| Shipping weight |
2 lbs (1 kg) |
| Vibration |
ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance |
| Safety |
CE, C-tick, CUL, UL |
| EMI/EMC |
CE, C-tick, FCC Class A, ICES, VCCI |
| MTBF |
30,000 hours |
| Warranty |
3 years parts and labor
|
